Scotsman CME1002R Especificaciones

INTRODUCTIONThis manual is intended as a reference for theinstallation and service of a Scotsman ice makermodel CME865R or CME1002R. Table of Contents

FOR THE ELECTRICIAN: Electrical Connections See the NAMEPLATE for current requirements todetermine wire size to be used for electricalhookup. The cube

FOR THE INSTALLER: Final Check List1. Is the ice maker cabinet in a room whereambient temperatures are within the minimum andmaximum temperatures spec

INITIAL START UPRemote Condenser:1. Check that all connections have been made.Ice Maker:1. Remove front panel by pulling out to unsnap.2. Remove two s

INITIAL START UP14. Check CUBE SIZEThe dimensions of the cubes are fixed by the sizeand shape of the molds on the evaporator plate,except that the thi

ADJUSTMENTSAdjustment Of The Timer & Switch AssemblyOne complete revolution of the cam on the timerrepresents eight minutes. If left as factory se

COMPONENT DESCRIPTIONCompressor ContactorThe compressor contactor carries the compressorline current. The contactor is wired so any controlin the pilo

COMPONENT DESCRIPTIONIce Level ControlThis electronic control uses sound waves tomeasure the distance between the bottom of theice machine and the top

COMPONENT DESCRIPTIONElectric Water Inlet Valve The water inlet solenoid valve fills the reservoirassembly with water. Excess water overflows outthe o

SERVICE SPECIFICATIONS: CME865RThe following numbers may be used as aguideline. There will be some variation from unit tounit. Numbers = (Condenser/Ca

SERVICE SPECIFICATIONS: CME1002RThe following numbers may be used as aguideline. There will be some variation from unit tounit. Numbers = (Condenser/C

PRE-INSTALLATION INFORMATIONThese two models are modular ice cube machinesthat are designed to be connected to a remotecondenser.The remote condenser

CLEANING & SANITIZINGA Scotsman Ice System represents a sizable investment of time and money in any company’s business. Inorder to receive the be

CLEANINGSANITIZE WATER SYSTEM1. Remove and discard all ice from the bin.2. Remove front panel.3. Drain the reservoir4. Prepare 2 gallons of an approve

FREEZING CYCLE OPERATIONWater from the sump assembly is pumped to thewater distributor system at the top of eachevaporator plate. From the water distr

HARVEST CYCLE - HOT GAS BYPASS When the timer switches the ice maker into theharvest cycle, high pressure, high temperaturerefrigerant gas being disch

SERVICE DIAGNOSISSYMPTOM POSSIBLE CAUSE PROBABLE CORRECTIONNo ice, machine does not run 1. No electrical power 1. Restore power2. Circuit breaker trip

SERVICE DIAGNOSISSYMPTOM POSSIBLE CAUSE PROBABLE CORRECTIONLow ice production 3. High head pressure, a result ofa dirty condenser 3. Clean condenser,

CONDITIONDETERMINE CAUSEPROBABLE CORRECTIONIce Machine does not run, it haspower to it, the high pressurecontrol is closed, the on/off switchis set to

TRANSDUCERLOCATIONTRANSDUCERREMOVAL OF TRANSDUCERPLUGCONNECTIONTRANSDUCERSOCKETREMOVAL AND REPLACEMENTTRANSDUCER1. Disconnect electrical power BEFORE

REMOVAL AND REPLACEMENT Water Distributor Tubes And Manifold Tubes To remove the water distributor tube and manifoldtube: 1. Pull out to unsnap catche

REMOVAL AND REPLACEMENT Water Pump1. Remove front panel.2. Remove evaporator cover.3. Unplug water pump electrical connection.4. Remove thumb screw re

ICE MACHINE SPECIFICATIONSAlways refer to the nameplate, located on the backof the cabinet, for the:••model number, ••serial number, ••basic electrica

REMOVAL AND REPLACEMENT Head Pressure Control Valve1. Remove side service panel, and top panel ifpossible.2. Discharge and recover refrigerant from th

VAPOR VAPOR TEMP. PRES. TEMP. PRESS.(DEG F) (PSIG) DEG F) (PSIG)-20 17 70 146-18 18 72 150-16 20 74 155-14 21 76 16

LIQUID CHARGING Instructions for R-404AIn preparation for charging, the low side hoseshould have a sight glass, and/or a restrictordevice (such as a &

ERC301 SPECIFICATIONS23 13⁄16"19 7⁄8"ERC DimensionsABFG33 3⁄8"10 3⁄4"16 3⁄4"11 5⁄8"CME865R & CME1002RDecember 1995Pa

FOR THE INSTALLER: Environmental LimitationsInstallation LimitationsThe ice making portion of this ice system isdesigned to be installed indoors, in a

FOR THE INSTALLER: Machine & Bin AssemblyOverview:This ice system consists of 4 major assemblies:1. The ice storage bin.2. The ice maker itself.3.

FOR THE PLUMBERWater SupplyThe recommended water supply line is a 3/8-inchO.D. tubing with a minimum operating pressure of20 PSIG and a maximum of 80

FOR THE INSTALLER: Remote CondenserLocate the condenser as near as possible to theinterior location of the ice maker. Location of the condenser is lim

FOR THE INSTALLER: Coupling InstructionsCAUTIONThe couplings on the sets of precharged lines areself sealing when installed properly. Carefullyfollow